How Do Thermal Bridges Weaken Insulation?
- Intermediate
- Article
- Ages 16+
- 7 min read

A thermal bridge is a spot on a wall, floor or roof that loses much more heat than the area around it, because a conductive material passes through or interrupts the insulation. Heat takes a shortcut there, like a short circuit, so the whole wall performs worse than the figure for its cavity insulation. To keep the benefit, the insulation has to be made continuous, not just thicker.
Contents
- Wall section (rectangle)
- Conductive framing bars (three solid grey bars)
- Insulated parts (two pale panels)
- Thick heat flow through the bars (two thick red arrows)
- Very thin heat flow through the insulation (thin red arrow)
What you will learn
- Explain why heat takes a shortcut through framing or a slab edge.
- Say how thermal bridges weaken insulation and what harm they do to a building.
- Compare ways to break a thermal bridge and know where they are easily missed.
Before you start
It helps to know that insulation is a layer that resists heat flow and that different materials conduct heat differently. Other terms are explained in the article.
How does a thermal bridge form?
A thermal bridge forms when a highly conductive material cuts through a low-conductivity layer. Thermal bridging occurs when a relatively small area of a wall, floor or roof loses much more heat than the surrounding area. A thermal bridge lets heat short-circuit the insulation. This typically happens when a material of high thermal conductivity, such as steel framing or concrete, penetrates or interrupts a layer of low-conductivity material such as insulation.
Thermal bridges also appear where building elements are joined, such as exposed concrete slabs and beams that abut or penetrate the exterior walls. And some come from construction, for example gaps in the insulation, which let heat escape around it and may also allow air leakage. Thermal bridging is most often caused by improper installation or by material choice and building design.
- Wall without a continuous layer (left)
- Wall with an added continuous insulating layer (right, green layer)
- Line dividing the two walls (dashed)
Why does a single stud weaken the whole layer of insulation?
Because a metal stud lets heat bypass the insulation. Steel studs act as strong thermal bridges in an insulated wall system. The steel stud lets heat bypass the insulation and greatly reduces the insulation's effectiveness.
The effect is measured with R-value, a measure of resistance to heat flow. Thermal bridging through steel studs lowers the effective R-value of the insulation, by an amount that depends on the size and spacing of the studs and on the R-value of the insulation. So the figure printed on the insulation is not yet the figure for the whole wall. The ASHRAE energy standard for buildings requires thermal bridging to be accounted for when determining or reporting R-values and U-factors of wall, floor and roof assemblies.
Masonry has a similar case. In a single-layer masonry wall the webs of the block and grouted cores can act as thermal bridges, particularly when the cores are insulated. The effect can be eliminated by putting insulation on the exterior or interior of the masonry rather than in the cores.
What harm do thermal bridges do to a building?
First more heat loss, then discomfort and damp. Possible effects are more heat loss through the wall, leading to higher operating costs, and local cold or hot spots on the interior at the bridge locations, causing occupant discomfort and sometimes condensation.
For steel studs, because they are typically in contact with the interior finish, local cold spots can develop at the stud locations. The effects of a thermal bridge can also be magnified by heat and moisture carried by moving air, particularly when warm, moist air enters the wall.
One important note: not all thermal bridges cause these severe effects. The severity of a thermal bridge should be judged by its effect on the overall energy performance of the building.
How is a thermal bridge broken?
The general principle is to make the insulation continuous, ideally at the design stage. Thermal bridges and the damage they cause can be avoided by several strategies, best applied at the design stage. After construction, repairing thermal bridges can be both costly and difficult.
A few specific ways:
- Put a continuous layer over the steel studs. The effects of steel studs can be reduced by adding a continuous layer of insulation over the steel stud and insulation layer.
- Insulate in the cavity of a masonry cavity wall. The insulation sits between the two masonry layers as one continuous layer, which minimises the effects of thermal bridging.
- Put the insulation in the right place at the slab edge. At the slab edge it is better to put insulation in the cavity than on the interior, because this isolates both the slab edge and the steel beam from the outside.
- Do not forget the parapet. A parapet is exposed to the outside on both sides, so it can act as a thermal fin, wicking heat up through the wall.
- Slab edge running through the insulation (left)
- Slab edge stopping short of continuous insulation (right)
- Line dividing the two ways (dashed)
Real-world example
Think of a thick winter coat with a metal zip running down the whole front. The coat keeps you warm everywhere except along the zip, where it feels much colder. The coat is the insulation and the zip is the thermal bridge. This is only an analogy: a real wall has many such paths and the difference depends on the design of each building.
Common misunderstandings
Thick insulation makes any wall well insulated. The R-value of the whole wall is lower than that of its insulation when conductive framing runs through it.
A thermal bridge only loses heat. It can also cause local cold spots, condensation and, in some cases, damage to materials.
Every thermal bridge is equally serious. Not all cause severe effects, and how serious one is has to be judged case by case.
Frequently asked questions
What is a thermal bridge?
An area of a wall, floor or roof that loses much more heat than the area around it because a conductive material cuts through the insulation.
Why are steel studs such strong thermal bridges?
Because a steel stud passes through the insulation and lets heat bypass it.
Is it easy to fix a thermal bridge once the building is finished?
Repairing thermal bridges after construction can be both costly and difficult, so they are best dealt with at the design stage.
Summary
- A thermal bridge is a shortcut for heat where a conductive material cuts through the insulation.
- Steel studs lower the effective R-value of the insulation, so the whole wall is worse than the figure on the insulation.
- Breaking the bridge means making the insulation continuous, ideally at the design stage.
Terms in this article
English and Vietnamese terms, with the meanings used here. Hover, tap or Tab to a term with a dotted underline for an explanation as you read.
- thermal bridgecầu nhiệt
- An area or part that conducts heat well and lets it take a shortcut past the insulation.
- thermal conductivityđộ dẫn nhiệt
- How readily a material lets heat pass; high for steel and concrete, low for insulation.
- R-value
- A measure of how well a layer or assembly resists heat flow; the higher, the better it resists.
- steel studthanh khung thép
- An upright steel member that frames a wall, usually sitting among the insulation.
- thermal breaklớp ngắt nhiệt
- A continuous insulating layer placed to cut the shortcut heat would take.
This article is not marked as viewed
Spotted something wrong or unsafe?
Tell the administrator by email. The message already has the article title and address.
More in this topic
IntermediateHow Does Heat Treatment Change a Metal's Properties?
Learn how heating and cooling change steel structure, how martensite and hardenability affect hardness, and why distortion and cracking matter.
5 min read
IntermediateHow Do Phase-Change Materials Store Heat?
A phase-change material holds a near-constant temperature while it melts. See how latent heat works, how to pick a melting point and where it falls short.
7 min read
IntermediateHow Does Thermal Mass Delay and Soften Heat Swings?
Thermal mass stores and releases heat; time lag, climate and wall design shape indoor temperature swings.
2 min read
IntermediateHow Do Low-E and Multi-Pane Glass Reduce Heat Loss?
Low-e coatings reduce radiant heat transfer, while extra panes and gas-filled gaps affect window heat flow and its U-factor.
2 min read
Sources
These sources are written for older readers. If they feel hard, read them with an adult.
- Thermal bridges in wall construction (CMHA)(opens in a new tab)
Concrete Masonry & Hardscapes AssociationTier C: other sourcesRead on November 14, 2026
