Skip to content
LSLab

How Do Panel Tilt and Orientation Affect Sunlight?

  • Starter
  • Article
  • Ages 10+
  • 5 min read
Rows of blue solar panels follow the slope of a red-tiled house roof, viewed from above.

Panel tilt and facing direction determine the angle at which direct sunlight reaches a module. Power density is greatest when the panel is perpendicular to the rays; angled light spreads over a larger surface (PVEducation on tilted surfaces, PVEducation on orientation and tilt). Since the sun’s position changes, a fixed panel cannot stay perpendicular all day (PVEducation).

Contents
Three parallel yellow rays point toward two rectangular plates set at different angles.
  • Panel facing the rays squarely (three rays and tilted plate)
  • Panel hit at a slant (three rays and upright plate)

Which tilt angle should you choose?

In an annual irradiance model for a fixed panel, a tilt equal to the location’s latitude gives the greatest total; the calculation excludes clouds (PVEducation). Seasonal needs can change the choice: steeper tilts suit places with high winter loads, while lower tilts receive a larger share of summer sunlight (PVEducation).

In a modeled latitude-tilt array in Albuquerque, tilt errors had the least effect near the latitude angle and a greater effect on horizontal arrays, except at the equator (Sandia).

A tilted panel sits between a yellow circle high on the left and a lower grey circle on the right, each with a ray toward the panel.
  • Tilted panel on the ground
  • High sun (yellow shape)
  • Low sun (grey shape)

Which direction should a panel face?

Most modules face toward the equator: typically south in the Northern Hemisphere and north in the Southern Hemisphere (PVEducation).

In an Albuquerque model of a latitude-tilt array, azimuth error had its greatest effect when the array pointed farther from due south (Sandia). That result describes a particular location and setup. An array can stay fixed or change its orientation over time with a tracker that reduces the angle between the sun and the array (Sandia).

A green arrow sits inside a large circle; below it is a tilted yellow rectangle on a short stand.
  • Ground where the panel stands (circle)
  • Direction of the equator (green arrow)
  • Panel (yellow rectangle)
  • Stand

From where is tilt measured?

Tilt is measured from the horizontal plane: a flat panel is at 0°, and a vertical panel is at 90° (PVEducation).

Terms in this article

English and Vietnamese terms, with the meanings used here. Hover, tap or Tab to a term with a dotted underline for an explanation as you read.

tilt anglegóc nghiêng
The angle between the panel surface and the horizontal.
orientationhướng tấm pin
The compass direction the panel face points to, for example south.
latitudevĩ độ
How far north or south of the equator a place lies.

This article is not marked as viewed

Spotted something wrong or unsafe?

Tell the administrator by email. The message already has the article title and address.

Report this article
  • A sunlit solar farm beside woodland and a reservoir, with distant wind turbines.
    Starter

    What Is Green Energy?

    Distinguish renewable energy from green power through solar and wind examples, while recognising environmental impacts that still matter.

    5 min read
  • A photovoltaic panel in the foreground with a wind turbine behind it under a bright sky.
    Starter

    How Do Solar and Wind Power Generate Electricity?

    Trace sunlight through photovoltaic cells and wind through a rotor and generator, comparing how each technology produces electricity.

    5 min read
  • A hydroelectric dam and spillway in the foreground, with a distant nuclear power station in daylight.
    Starter

    How Do Renewable and Low-Carbon Energy Differ?

    Two labels, two questions: renewable is about supply that nature replenishes, low-carbon about emissions when power is made. Nuclear shows how they differ.

    5 min read
  • An electric motor with exposed copper windings coupled by a shaft to a load device on a laboratory bench.
    Starter

    What Does Energy Conversion Efficiency Mean?

    Efficiency is useful energy divided by total energy in; see where the rest goes as waste heat, with a car, a power plant and a solar cell as examples.

    5 min read
See all articles of the topic

Sources

These sources are written for older readers. If they feel hard, read them with an adult.