How Do Vacuum Insulation Panels Work?
- Basic
- Article
- Ages 14+
- 6 min read

A vacuum insulation panel (VIP) is a fine porous core with the air removed, sealed in an airtight barrier film. Tiny pores make air pass heat poorly and evacuation further reduces gas heat transfer, so the panel is thin yet insulates well. If the film is punctured, the vacuum is lost.
Contents
- Outer barrier film
- Fine porous core
What you will learn
- Name the three parts of a VIP and what each does.
- Explain why a very thin panel can insulate so well.
- State the weak points of VIPs and how people work around them.
Before you start
Know that heat travels by conduction and convection, and that still air is a fairly good insulator.
What parts does a VIP have?
A core, a barrier film and the vacuum inside. A VIP is essentially a highly insulating core sealed within an airtight multilayer barrier film, with the air inside removed to create a deep vacuum.
The core. The core is typically made of pyrogenic silica or fine glass fibers and has an extremely fine pore structure, under 60 nanometers. That structure limits the ability of air molecules to transfer heat, even before the vacuum is applied. The core is also designed to resist compression under the high loads it meets when the vacuum is applied.
The barrier film. It is a multilayer laminated plastic film with thin metal coatings that block the passage of gases and moisture.
The vacuum. Evacuating the air drastically reduces air conduction and convection through the core.
- Core in air
- Core after the vacuum
Why does a thin panel insulate so well?
Because the core and the vacuum together block the heat carried by air. A fine porous core makes it hard for gas molecules to pass heat on, and the vacuum removes those very molecules. The result: fresh, undamaged panels can have a thermal conductivity as low as 0.004 W/m·K, about one-fifth of common foam insulations. VIPs also have an extremely high thermal resistance of around R35 per inch.
High performance in minimal thickness is particularly valuable where space is constrained.
The edge is a weaker spot. The edges, where the barrier film is sealed, transfer more heat than the center, so the welded flaps are folded flat or taped to reduce these edge effects.
- VIP: very thin
- Ordinary foam: much thicker
- The same heat resistance
What makes a VIP lose its performance?
A punctured film, air leaking in slowly, and practical limits. If the barrier film is punctured, the vacuum is lost and thermal performance drops, though the core still insulates slightly better than rigid foam. Over time, small amounts of air may leak in, slowly reducing performance over many years.
There are other limits. Panels cannot be cut to fit on site, so designs must accommodate fixed panel dimensions. Per unit of R-value, VIPs currently cost more than traditional insulation.
- Intact panel
- Punctured panel, air leaks in
How are panels protected from damage?
By careful installation and by better barrier film. The barrier film can be easily damaged during transportation, installation and service life. Oak Ridge National Laboratory (ORNL) has developed a self-healable barrier film that instantly self-heals damage caused by punctures.
For installation, girts let exterior cladding be attached without puncturing the panels with fasteners.
- Wall
- VIP
- Girts
- Exterior cladding
Real-world example
Picture a hypothetical old house with thin walls and no room to thicken them. Adding a layer of VIP on the outside adds very little thickness but resists a lot of heat. Installers must place panels of the size prepared in advance and avoid drilling or nailing into them. This is an illustrative model, not a description of a particular building.
Common misunderstandings
The vacuum alone is the insulator. The fine porous core plays a big part: it limits heat transfer by air even before the vacuum is applied, and it stops the panel collapsing.
A punctured panel is useless. The vacuum is lost and performance drops, but the core still insulates slightly better than rigid foam.
You can cut a VIP to fit on site like ordinary foam. Panels cannot be cut to fit on site, because cutting would puncture the barrier film.
Frequently asked questions
What is a vacuum insulation panel made of?
A fine porous core, typically pyrogenic silica or fine glass fibers, sealed in a multilayer barrier film with the air removed.
Why do VIPs cost more?
Per unit of R-value, VIPs currently cost more than traditional insulation.
Does a VIP last a long time?
Over time, small amounts of air may leak in, slowly reducing thermal performance over many years.
Summary
- A VIP has a fine porous core, an airtight barrier film and a vacuum inside.
- The small-pored core and the vacuum make a thin panel insulate well, while the edge transfers more heat.
- A punctured film or leaking air cuts performance, so careful installation and better barrier films matter.
Terms in this article
English and Vietnamese terms, with the meanings used here. Hover, tap or Tab to a term with a dotted underline for an explanation as you read.
- vacuum insulation paneltấm cách nhiệt chân không
- A panel made of an insulating core with the air removed, sealed in a barrier film.
- barrier filmmàng chắn
- The multilayer film around the core that keeps gas and moisture out.
- corelõi
- The fine porous inside of the panel that stops it collapsing under the vacuum.
- thermal conductivityđộ dẫn nhiệt
- How readily a material passes heat on; the lower, the better it insulates.
- R-valuetrị số R
- A measure of how well a material resists heat flow; the higher, the better it insulates.
- edge effecthiệu ứng mép
- Heat passing through a panel's edge more than through its center.
This article is not marked as viewed
Spotted something wrong or unsafe?
Tell the administrator by email. The message already has the article title and address.
More in this topic
BasicHow Do Strength, Hardness and Ductility Differ?
Tell strength, hardness and ductility apart through yield strength, tensile strength and elastic and plastic deformation to read mechanical properties.
5 min read
BasicWhat Do Tensile and Hardness Tests Measure?
See how a tensile test records force and extension, why results become stress and strain, and what a hardness test derives from the dent of an indenter.
5 min read
BasicHow Do Ashby Charts Help Compare Materials?
Understand how an Ashby chart puts many materials on two properties, why it uses log scales and how sliding an index line picks a material.
5 min read
BasicHow Does Material Selection Go from Needs to Options?
Follow material selection from functional requirement, fixed and free variables to a performance index and a shortlist that still needs checking.
5 min read
Sources
These sources are written for older readers. If they feel hard, read them with an adult.
- Vacuum Insulation Panels: High-Performance Building Envelope Insulation, Ideal for Retrofit Upgrades (Insulation Outlook)(opens in a new tab)
Insulation Outlook (NIA)Tier C: other sourcesRead on November 7, 2026
- Self-Healing Films for Vacuum Insulation Panels (Final Report)(opens in a new tab)
Oak Ridge National LaboratoryTier A: government, standards or research bodiesRead on November 7, 2026
