Skip to content
LSLab

How Does Temperature Change Semiconductor Carriers?

  • Starter
  • Article
  • Ages 10+
  • 6 min read
A silicon wafer rests on a test stage as laboratory probes touch its surface.

Temperature strongly affects the carrier population in an intrinsic semiconductor such as pure silicon. In the intrinsic model, the conduction band is empty at absolute zero. As the material warms, heat lifts some electrons into the conduction band and leaves holes behind. Both electrons and holes carry charge, so current in an intrinsic semiconductor is highly sensitive to temperature.

Contents
Dots represent bound electrons. Excitation creates a free carrier and leaves a hole; this is a schematic, not an electron escaping the material.
  • Schematic lattice with bound electrons
  • Hole: the cell left with an empty ring
  • Free electron outside the lattice
  • Direction the electron leaves

What you will learn

Before you start

You only need to know that an electron is a tiny particle that carries charge. Nothing else is required.

What is a charge carrier, and where do holes come from?

A charge carrier is a charged particle that moves through a material and makes up an electric current. A semiconductor has two kinds: electrons and holes.

Picture a silicon crystal. The figure uses dots at bonds to represent bound electrons; it does not mean real electrons are stationary points. At any temperature above absolute zero, there is still a finite probability that an electron is knocked loose from its position. The spot it leaves is a shortage of one electron, called a hole.

When a voltage is applied, both the electron and the hole add to a small current. A hole is not a particle that really travels. Other electrons hop in to fill the empty spot, and overall the hole seems to drift the opposite way to the free electrons.

What does heat do to charge carriers?

Heat can excite electrons from the valence band into the conduction band, where they can contribute to conduction. The valence band is the range of energies for electrons still tied to their atoms. The conduction band is the higher range where electrons take part in conduction.

In the intrinsic model, at absolute zero the conduction band holds no electrons even though plenty of states are free. At high temperatures the conduction band has a finite population of conducting electrons. The number climbs fast as things warm: in an illustrative calculation, the conduction electron population in silicon doubles over about an 8 degree temperature rise, and in germanium for about 13 degrees.

That is why the current in a pure semiconductor is very sensitive to temperature. A little extra warmth brings more carriers, and the current follows.

When it warms, some electrons jump from the lower block to the upper block and leave empty rings.
  • Valence band (lower block)
  • Conduction band (upper block)
  • Electrons that reached the conduction band
  • Holes left in the valence band

Why does a semiconductor differ from an insulator and a metal?

The difference is the width of the band gap, the energy gap between the valence band and the conduction band. There are three cases.

In an insulator, heat usually cannot push electrons across the large gap. In a metal, the conduction band already holds electrons. A semiconductor sits in between, so heat can create carriers and temperature matters a lot.

The band gap also explains why two semiconductors react differently. Because of its larger band gap, silicon has fewer conduction electrons than germanium at any given temperature.

The distance between the two blocks shrinks from the left pair to the right pair, until they overlap.
  • Conduction band in the three materials (upper blocks)
  • Valence band in the three materials (lower blocks)
  • Band gap: two-headed arrow, long then short
  • The overlap in the right pair

How does doping relate to temperature?

Doping is another way to increase the carrier population: change the material’s composition rather than simply raising its temperature. A small amount of foreign atoms is added to the crystal. Impurity atoms with five valence electrons add free electrons and greatly raise conductivity, while impurity atoms with three valence electrons create holes. A small percentage of doping material is enough to raise conductivity dramatically.

Thermal excitation and doping are two carrier-supply mechanisms, but not an exhaustive list for every device. The figure illustrates dopants under conditions with free carriers; it does not imply that doping removes temperature effects.

Dopants can supply electrons or create holes. The sketch shows carriers under conditions where they can contribute to conduction.
  • Ordinary atoms and bound electrons
  • Impurity atoms (amber cells)
  • Extra free electron (left)
  • Hole created by the impurity (right)

Real-world example

Think of a playground with a low fence. The children sitting still inside are electrons in the valence band. On a cool day fewer children climb out. On a hot, lively day a few climb over the fence and run across the grass on the other side, leaving empty spots in the playground. The livelier it gets, the more children get out. This is only an illustration; real electrons have no legs to climb with.

Common misunderstandings

A hole is a real particle running through the material. It is a missing electron. Other electrons hop in to fill the spot, so the hole seems to move the other way.

A semiconductor conducts better when cold, like many metals. At absolute zero the conduction band of a pure semiconductor holds no electrons. Warming is what creates carriers.

Silicon and germanium have the same number of carriers at the same temperature. Their band gaps differ, so their numbers of conduction electrons differ too.

Frequently asked questions

Does a higher temperature make a semiconductor conduct more?

In the intrinsic model considered here, heat increases the conduction-electron and hole populations. Carrier count alone does not determine the current of every doped device. In an illustrative calculation, the conduction electron population in silicon doubles over about an 8 degree temperature rise.

Why does a metal not need heat to conduct?

In the band model used here, the metal has overlapping bands, so electrons are already available for conduction.

How are a hole and an electron different?

An electron is a charged particle. A hole is a missing electron, yet under a voltage it adds to the current too.

Summary

Terms in this article

English and Vietnamese terms, with the meanings used here. Hover, tap or Tab to a term with a dotted underline for an explanation as you read.

charge carrierhạt tải
A charged particle that moves through a material and makes up an electric current; in a semiconductor these are electrons and holes.
electron
A very small particle with negative charge; an electron knocked loose from its position can move freely in a semiconductor.
holelỗ trống
A missing electron in the crystal lattice; under a voltage it also adds to the current.
conduction bandvùng dẫn
The high range of energies where electrons move freely and take part in conduction.
valence bandvùng hóa trị
The range of energies of electrons still tied to their atoms.
band gapvùng cấm
The energy gap between the valence band and the conduction band.
dopingpha tạp
Adding a small amount of foreign atoms to a crystal to supply extra free electrons or holes.
semiconductorchất bán dẫn
A material whose band gap is small enough for heat to lift electrons into the conduction band.
absolute zerođộ không tuyệt đối
The lowest possible temperature; there the conduction band of a pure semiconductor holds no electrons.

This article is not marked as viewed

Spotted something wrong or unsafe?

Tell the administrator by email. The message already has the article title and address.

Report this article
See all articles of the topic

Sources

These sources are written for older readers. If they feel hard, read them with an adult.